. Check that the exhaust pipe is not smooth. If it doesn't work, clean or replace it. Drive for a while to check whether the oil is missing and whether the exhaust pipe is still injecting oil. Measure the cylinder pressure, and the cylinder pressure is normal: that should be the burning oil caused by the aging and damage of the valve oil seal, and replace the valve oil seal. It is recommended to replace all oil seals.
If there is an oil leak, we should immediately contact a professional technician for repair. Once we find the problem of engine oil, we need to carry out careful inspection and repair. First of all, we can check whether there is any leakage of the oil filter. If so, we need to replace the oil filter.
Possible reasons: the cylinder, piston and piston ring wear exceeds the limit, or the piston ring is opposite, the piston ring is broken, the cylinder is pulled, the cylinder leaks into the crankcase, and the oil is blown out; the oil is added too much, the oil is stirred and discharged;... It is recommended to investigate and solve it from shallow to deep.
If it's just a drop of oil, the engine power performance can still guarantee normal operation, so it's not a serious problem.
The newly overhauled engine has some cases of burning lubricating oil, whichIt's normal. As long as you avoid the four taboos and often check the height of the coolant and lubricant, there should be no big problem.
Don't wait until there is a breakdown to pay attention to it. The consequences can be unimaginable. Secondly, it may also be because the valve rod and the valve duct are seriously worn, or the sealing is too poor, resulting in too large a gap, resulting in the situation of oil, which needs to be repaired in time.
1. Check whether the engine cylinder pressure is normal and whether there is air leakage. Clean the oil circuit, replace the spark plugs, filters, etc. Check whether the four wheels are dragging brakes.Check whether the quality of the oil is good. If not, replace the new oil.
2. Insufficient oil supply. The fuel system should be able to spray well-atomized fuel into the cylinder in a timely and appropriate amount. If the fuel system fails and the amount of oil in the injector cylinder is small, the heat generated by combustion is reduced. When the heat is reduced to the point that it cannot meet the requirements of the engine load, the engine is weak.
3. The reasons for Chaiwei's engine's boring hill climbing are as follows: excessive carbon accumulation: it is recommended to check whether the engine has accumulated too much carbon, which may generally lead to excessive carbon accumulation. Insufficient oil supply: The fuel system should be able to inject atomized fuel into the cylinder in a timely and appropriate manner.
1. Improper maintenance: The correct method is not mastered during maintenance, and low-purity gasoline or fuel oil is used, which will cause damage to the Weichai Guoliu natural gas egr valve. It is necessary to maintain the EGR valve regularly, clean up the accumulated carbon, and use gasoline and fuel additives with the correct label.
2. Engine jitter and lack of cylinder. Common reasons include spark plug ignition failure, ignition coil leakage, internal short circuit of the electric coil causing intermittent non-jump. The rust of the engine exhaust pipe causes the exhaust pipe to make a poof, and the exhaust gas is discharged from the middle without passing through the exhaust pipe, resulting in abnormal engine noise.
3. Simply put, the engine is an energy conversion mechanism, that is, the thermal energy of gasoline (diesel) is converted into mechanical energy through dense, which is the most basic principle of the engine.
4. Check whether there is too little fuel in the fuel tank and whether the pressure in the fuel pipe is unstable.
Global trade compliance best practices-APP, download it now, new users will receive a novice gift pack.
. Check that the exhaust pipe is not smooth. If it doesn't work, clean or replace it. Drive for a while to check whether the oil is missing and whether the exhaust pipe is still injecting oil. Measure the cylinder pressure, and the cylinder pressure is normal: that should be the burning oil caused by the aging and damage of the valve oil seal, and replace the valve oil seal. It is recommended to replace all oil seals.
If there is an oil leak, we should immediately contact a professional technician for repair. Once we find the problem of engine oil, we need to carry out careful inspection and repair. First of all, we can check whether there is any leakage of the oil filter. If so, we need to replace the oil filter.
Possible reasons: the cylinder, piston and piston ring wear exceeds the limit, or the piston ring is opposite, the piston ring is broken, the cylinder is pulled, the cylinder leaks into the crankcase, and the oil is blown out; the oil is added too much, the oil is stirred and discharged;... It is recommended to investigate and solve it from shallow to deep.
If it's just a drop of oil, the engine power performance can still guarantee normal operation, so it's not a serious problem.
The newly overhauled engine has some cases of burning lubricating oil, whichIt's normal. As long as you avoid the four taboos and often check the height of the coolant and lubricant, there should be no big problem.
Don't wait until there is a breakdown to pay attention to it. The consequences can be unimaginable. Secondly, it may also be because the valve rod and the valve duct are seriously worn, or the sealing is too poor, resulting in too large a gap, resulting in the situation of oil, which needs to be repaired in time.
1. Check whether the engine cylinder pressure is normal and whether there is air leakage. Clean the oil circuit, replace the spark plugs, filters, etc. Check whether the four wheels are dragging brakes.Check whether the quality of the oil is good. If not, replace the new oil.
2. Insufficient oil supply. The fuel system should be able to spray well-atomized fuel into the cylinder in a timely and appropriate amount. If the fuel system fails and the amount of oil in the injector cylinder is small, the heat generated by combustion is reduced. When the heat is reduced to the point that it cannot meet the requirements of the engine load, the engine is weak.
3. The reasons for Chaiwei's engine's boring hill climbing are as follows: excessive carbon accumulation: it is recommended to check whether the engine has accumulated too much carbon, which may generally lead to excessive carbon accumulation. Insufficient oil supply: The fuel system should be able to inject atomized fuel into the cylinder in a timely and appropriate manner.
1. Improper maintenance: The correct method is not mastered during maintenance, and low-purity gasoline or fuel oil is used, which will cause damage to the Weichai Guoliu natural gas egr valve. It is necessary to maintain the EGR valve regularly, clean up the accumulated carbon, and use gasoline and fuel additives with the correct label.
2. Engine jitter and lack of cylinder. Common reasons include spark plug ignition failure, ignition coil leakage, internal short circuit of the electric coil causing intermittent non-jump. The rust of the engine exhaust pipe causes the exhaust pipe to make a poof, and the exhaust gas is discharged from the middle without passing through the exhaust pipe, resulting in abnormal engine noise.
3. Simply put, the engine is an energy conversion mechanism, that is, the thermal energy of gasoline (diesel) is converted into mechanical energy through dense, which is the most basic principle of the engine.
4. Check whether there is too little fuel in the fuel tank and whether the pressure in the fuel pipe is unstable.
Real-time delivery time predictions
author: 2024-12-23 21:33International vendor verification
author: 2024-12-23 21:31Global trade analysis dashboard
author: 2024-12-23 21:25Granular HS code detail for compliance officers
author: 2024-12-23 23:50How to reduce customs compliance risk
author: 2024-12-23 22:40How to reduce supply chain overheads
author: 2024-12-23 22:24172.38MB
Check595.63MB
Check697.25MB
Check912.87MB
Check897.17MB
Check283.36MB
Check877.11MB
Check884.97MB
Check118.33MB
Check358.34MB
Check946.36MB
Check631.78MB
Check597.82MB
Check196.27MB
Check194.87MB
Check146.37MB
Check434.92MB
Check389.67MB
Check469.41MB
Check357.77MB
Check164.38MB
Check994.81MB
Check394.73MB
Check628.21MB
Check351.68MB
Check658.96MB
Check838.82MB
Check699.38MB
Check114.62MB
Check929.27MB
Check423.62MB
Check434.75MB
Check481.56MB
Check275.52MB
Check492.37MB
Check715.33MB
CheckScan to install
Global trade compliance best practices to discover more
Netizen comments More
2727 HS code-driven sectoral analysis
2024-12-23 23:42 recommend
1374 Canada HS code classification assistance
2024-12-23 22:59 recommend
1889 Bio-based plastics HS code classification
2024-12-23 22:20 recommend
2064 Industry-specific trade growth forecasts
2024-12-23 21:53 recommend
432 How to interpret trade volume changes
2024-12-23 21:24 recommend